perhaps this will be helpful
https://support.zoneedit.com/en/knowledgebase/article/dynamic-dns
https://support.zoneedit.com/en/knowledgebase/article/dynamic-dns
Setting Up Dynamic DNS For Your Domain
- Thread starter zeadmin
- Start date
Erik508
New Member
I appreciate the link. I have read this, and I have a client setup. However, I would like to write my own client.
Erik508
New Member
I am looking for documentation on the API - is it not published anywhere?hi again .. of course.... many subscribers do just that.
regards,.
Erik508
New Member
I see the existing third party clients call an API to update the dns, one uses api.cp.zoneedit.com, another one uses dynamic.zoneedit.com. There are various parameters such as hostname and ip address. I am looking for documentation on these APIs
I can reverse engineer what the other clients do, but I would much rather use the actual API documentation
Last edited:
Hi again we do not have a help article for zoneedit but we do for easyDNS.. substitute the connecting URL for that of zoneedit
kb.easydns.com
regards.
How To Use Dynamic DNS – easyDNS Technologies Inc
kb.easydns.com
regards.
Erik508
New Member
Exactly what I was after, thanks!Hi again we do not have a help article for zoneedit but we do for easyDNS.. substitute the connecting URL for that of zoneedit
How To Use Dynamic DNS – easyDNS Technologies Inc
regards.
Andrew Leahy
New Member
Hi, I'm having a problem setting up dynamic dns using ddclient on Linux.
It always says I'm hitting the zoneedit endpoint too often, even if I wait an hour.
Is the 10minute wait interval just for that specific hostname or does it apply for ANY DDNS request on a host in the domain?
Thanks
Partial debug...
It always says I'm hitting the zoneedit endpoint too often, even if I wait an hour.
Is the 10minute wait interval just for that specific hostname or does it apply for ANY DDNS request on a host in the domain?
Thanks
Partial debug...
Andrew Leahy
New Member
Thanks. I don't believe there are any other dynamic updates happening on the zone. This is the first time I've tried to set this up.
How do I find out what is causing the persistent "go away for 10minutes" wait?
Is there a log or something I can check on the cp.zoneedit.com client portal?
Last edited:
hi again.. our logs only indicate the same concern:
Jun 21 12:40:59 dyn02-zpc zoneedit: /var/www/dynamic.zoneed <-@115.69.13.48> Update frequency too high for piclamp17.sstars.ws. Increase time between updates to 600 seconds or more. (Delta 313)
Jun 21 12:41:00 dyn02-zpc zoneedit: /var/www/dynamic.zoneed <-@115.69.13.48> Dynamic request: [client] => zoneedit_legacy; [rsp_ident] => zoneedit; [username] => aleahy2; [password] => ****; [hostname] => piclamp17.sstars.ws; [ip] => 1.2.3.4; [wildcard] => ; [token] => ****;
Jun 21 12:41:00 dyn02-zpc zoneedit: /var/www/dynamic.zoneed <-@115.69.13.48> Update frequency too high for piclamp17.sstars.ws. Increase time between updates to 600 seconds or more. (Delta 314)
I am looking into what yo might be able to do to fix this.
Jun 21 12:40:59 dyn02-zpc zoneedit: /var/www/dynamic.zoneed <-@115.69.13.48> Update frequency too high for piclamp17.sstars.ws. Increase time between updates to 600 seconds or more. (Delta 313)
Jun 21 12:41:00 dyn02-zpc zoneedit: /var/www/dynamic.zoneed <-@115.69.13.48> Dynamic request: [client] => zoneedit_legacy; [rsp_ident] => zoneedit; [username] => aleahy2; [password] => ****; [hostname] => piclamp17.sstars.ws; [ip] => 1.2.3.4; [wildcard] => ; [token] => ****;
Jun 21 12:41:00 dyn02-zpc zoneedit: /var/www/dynamic.zoneed <-@115.69.13.48> Update frequency too high for piclamp17.sstars.ws. Increase time between updates to 600 seconds or more. (Delta 314)
I am looking into what yo might be able to do to fix this.
Andrew Leahy
New Member
Hi, was there any outcome from this?
I am having trouble getting the Javascript Client to update my DDNS DYN record nas.microconcepts.com.au
I entered my ZE name,token and the url. Click "Start" the current time is displayed and thats it.
Sniffed the traffic with Wireshark and a healthy TLS stream. Cannot get a response displayed?
I entered my ZE name,token and the url. Click "Start" the current time is displayed and thats it.
Sniffed the traffic with Wireshark and a healthy TLS stream. Cannot get a response displayed?
I'm trying to get dynamic updates for the wildcard record to work and I keep getting the NO_SERVICE response and that I've specified an invalid hostname.
https://<user>:<token>@api.cp.easydns.com/dyn/generic.php?hostname=<mydomain>.com&wildcard=yes&myip=1.1.1.1
I realize that IP is cloudflares, just trying to see if I can set it from what it currently is.
That's the string I'm using. I have an @ record specified as a DYN record and have a token. I've tried specifying @.mydomain.com as well. I've tried without the wildcard=yes on a different dyn record and get the same outcome. I'm missing something, just unsure that that is. UPdates manually just fine.
https://<user>:<token>@api.cp.easydns.com/dyn/generic.php?hostname=<mydomain>.com&wildcard=yes&myip=1.1.1.1
I realize that IP is cloudflares, just trying to see if I can set it from what it currently is.
That's the string I'm using. I have an @ record specified as a DYN record and have a token. I've tried specifying @.mydomain.com as well. I've tried without the wildcard=yes on a different dyn record and get the same outcome. I'm missing something, just unsure that that is. UPdates manually just fine.
Standing by to answer which of these. #176 or #177?